PlugSolar
How it works

How does plug-in solar work?

A microinverter turns the panels' DC into 120 V AC, and a cord feeds it into an outlet, where your devices use it first. What your breaker and meter see, and why it stops in a blackout.

How does plug-in solar work?
Illustration: AI-generated image, not a product photo.
On this page
  1. What the microinverter does
  2. The cord and the outlet
  3. Why your breaker can't see the kit
  4. Your home uses the solar power first
  5. What your meter sees
  6. Does it work in a blackout?

Plug-in solar is a short chain. The panels make direct current (DC), a microinverter converts it to the 120 V alternating current (AC) your outlets already carry, and a cord feeds that into a household circuit. Anything switched on nearby uses the solar power before it draws from the grid.

Key points

  • A 1,200 W kit adds 10 A to the circuit, current your breaker never sees because it counts only what arrives from the grid.
  • Exports usually earn nothing, and a meter that can't track them may bill them as usage. Ask your utility which meter you have.
  • No power in a blackout: the kit shuts off with the grid unless it has a battery with its own outlets.

What the microinverter does

Two short leads carry the panel's DC into the microinverter, a small box mounted behind the panel. Hoymiles' plug-in model works with 16 to 60 V from the panel and puts out 120 V at 60 Hz.

The back of a black solar panel on a ground frame, two short cables running from it into a small gray inverter box with a green light, and one cord leading away toward the house
Two short DC leads go into the microinverter; one AC cord comes out.

Its output has to match the grid's voltage and frequency, so it checks the grid before starting. The APsystems EZ1 waits for five minutes of stable grid, and Hoymiles' manual tells you to allow five minutes for its kit to start.

Once running, it keeps watching and shuts off as soon as the grid goes away. This is called anti-islanding, and the state laws require it: Utah and Vermont call for a feature that stops the system from energizing the building in an outage. Grid-tied inverters are generally tested to stop within 2 seconds. Maine's law sets 0.2 seconds.

That shut-off does two jobs. It keeps a downed line dead for the crews repairing it, and it keeps the plug safe in your hand. Pull the plug and the kit loses the grid, so the inverter should stop powering its prongs. If it doesn't, UL warns, accessible plug blades "can become energized when exposed to sunlight." Colorado Springs Utilities advises a pause after unplugging, to be sure the system is de-energized.

The cord and the outlet

The inverter's AC cord ends in a normal grounded three-prong plug. Hoymiles ships it 15 feet long, with 14-gauge wire. It goes straight into a grounded wall outlet, often an outdoor one.

A solar kit's single plug in an outdoor wall outlet under a closed clear weatherproof cover, its cord running toward the panels
One plug, straight into a covered outdoor outlet.

Outside is where ground-fault circuit interrupter (GFCI) protection matters: UL calls it a critical safety feature in outdoor and wet locations, and notes that a plug-in system can compromise it.

Plug the kit directly into a wall outlet. Never run it through an extension cord, a power strip or a cord with plugs on both ends. Hoymiles' manual permits only cables and parts from Hoymiles or makers it authorizes. The Consumer Product Safety Commission warns that male-to-male cords have "exposed prongs that can become energized."

Why your breaker can't see the kit

The breaker sits in your electrical panel and measures only the current arriving from the grid. The kit feeds current into the same circuit from the far end, at its outlet, out of the breaker's view.

To get amps, divide watts by volts. At 120 V, a 1,200 W kit adds 10 A, an 800 W kit about 6.7 A and a 420 W kit 3.5 A. A 15 A breaker guards 14-gauge wire; a 20 A breaker guards 12-gauge. Suppose the devices past the kit's outlet pull all the current the breaker allows. The wire from the kit's outlet to those devices carries the grid's share plus the kit's, and the breaker counts only the grid's.

Kit (AC output)15 A circuit, worst case20 A circuit, worst case
420 W (3.5 A)18.5 A (123%)23.5 A (118%)
800 W (6.7 A)21.7 A (144%)26.7 A (133%)
1,200 W (10 A)25 A (167%)30 A (150%)

Those numbers assume heavy loads on that circuit beyond the kit's outlet. Most people can't see how their outlets are wired. In UL's words, the combined current from the utility and the kit "can exceed conductor ratings without tripping the circuit breaker." Colorado Springs Utilities advises keeping power-hungry appliances off the kit's circuit.

The state laws cap the size. Utah allows up to 1,200 W. Maine allows 420 W without an electrician. Above that, it requires a licensed electrician and a dedicated circuit with one outlet, the fix UL lists against overloads. If you don't know what else shares your circuit, a licensed electrician can find out. A 2026 amendment proposal from a plug-in solar maker would add a plug-in solar category to the National Electrical Code; the maker points out that the code has none yet.

Your home uses the solar power first

Power on the circuit flows to whatever is running. The grid makes up the difference, second by second, automatically. Say your devices draw 300 W and the kit makes 500 W: the house runs on solar, and 200 W leaves through the meter.

A kit can't deliver more than its AC output; APsystems' EZ1 tops out at 900 W. Across a year, an 800 W kit tilted south makes roughly a tenth of what an average US home uses. Our complete guide to plug-in solar works out what that saves.

What your meter sees

The utility meter sits where the grid enters your home, and it sees only the net flow. While the kit runs, less power comes in. When the kit makes more than the house uses, the surplus flows out to the grid.

What happens to that exported power depends on the meter. Under net metering, older meters could spin backward. In 2022, the federal Energy Information Administration counted about 73% of residential meters as smart meters, but a meter's type and setup decide whether it tracks exports. If it can't, the Maryland Public Service Commission warns, it may record them as zero or add them to your usage by mistake.

Connecticut puts that warning in its law: every device must say that excess generation will be "charged to the customer as usage" unless your meter allows net metering. Vermont permits plug-in devices only on smart meters. Utah, Maine and Vermont keep plug-in kits outside their net metering rules, and Vermont says exported power goes unpaid.

Some setups avoid exports altogether. For the EZ1, APsystems sells an APmeter ($90 on its US site, November 2026) that reads the flow at your panel and turns the inverter down. A qualified professional should install it. Your state's page in our tracker shows what its law says, and your utility can tell you how your meter counts exports.

Does it work in a blackout?

Not on its own. The same anti-islanding shut-off stops the kit the moment the grid goes down.

A battery changes part of that. EcoFlow's STREAM Ultra stores 1.92 kWh. In an outage it stops feeding the grid, and appliances plugged into its own outlets run on the battery or the panels.

Sources

  1. Safety Considerations for Plug-In Photovoltaic (PIPV) Systems, UL Solutions, 2026.
  2. HiFlow Pro LV Series Microinverter User Manual (North America, REV 1.1), Hoymiles, 2026-07-16.
  3. EZ1 – Consumers, APsystems, 2026.
  4. H.B. 340 Solar Power Amendments (Enrolled Copy), Utah State Legislature, 2025.
  5. No. 149. An act relating to plug-in photovoltaic devices. (S.202), Vermont General Assembly, 2026-06-16.
  6. An Act to Make Small Plug-in Solar Generation Devices Accessible for All Maine Residents to Address the Energy Affordability Crisis (Public Law, chapter 644), Maine Legislature, 2026-04-06.
  7. Public Act No. 26-127 (House Bill No. 5340), Connecticut General Assembly, 2026-06-04.
  8. Unintentional Islanding Evaluation Utilizing Discrete RLC Circuit Versus Power Hardware-in-the Loop Method (Sandia National Laboratories, SAND2019-6655C), OSTI (U.S. Department of Energy), 2019.
  9. Plug-in solar energy, Colorado Springs Utilities, 2026.
  10. CPSC Warns Consumers to Stop Using Male-to-Male Extension Cords, Secures Delisting Commitments from e-Commerce Platforms, U.S. Consumer Product Safety Commission, 2026-03-31.
  11. Article 240, Part 1 — Overcurrent Protection, IAEI Magazine, 2013-01-16.
  12. NFPA 70 Proposed TIA Log No. 1951: Plug-in Photovoltaic (PIPV) System and Part IV, 705.100, NFPA, 2026.
  13. How much electricity does an American home use?, U.S. Energy Information Administration, 2024-01-08.
  14. How many smart meters are installed in the United States, and who has them?, U.S. Energy Information Administration, 2023-10-20.
  15. Distributed Generation: An Overview of Recent Policy and Market Developments (American Public Power Association), U.S. Department of Energy, 2013-11.
  16. Balcony Solar, Maryland Public Service Commission, 2026.
  17. EcoFlow STREAM Ultra, EcoFlow, 2026.
  18. Specific photovoltaic power output (PVOUT), crystalline silicon at optimum tilt, Global Solar Atlas (World Bank Group, Solargis), 2025.

Read next

How it works

Plug-In Solar Panels: The Complete US Guide (2026)

A plug-in kit is a few panels and a microinverter that plug into a wall outlet. As of November 2026, ten states have a law for it and six are in effect; an 800 W kit saves about $75 to $295 a year.

Updated Nov 15, 2026